OB15 evolution: the v2 two-arm frame on a red base, the v3 robot with lift and head camera, and OB15 sorting coloured blocks into bowls

personal project · ongoing

ob15 — bimanual mobile manipulator

A two-armed mobile robot for imitation learning, built for under £1,000 on a home 3D printer: omni-wheel base, 600 mm lift, pan-tilt head camera and two SO-101 arms, controlled in VR.

code → github.com/ImpurestTadpole/ob15

01 · the problem

Research robots cost as much as a car

Mobile bimanual platforms like Stanford’s Mobile ALOHA cost around $30,000, so robot learning stays in well-funded labs. Students, researchers and hobbyists working with limited space and budgets are locked out.

02 · the hypothesis

Open hardware is good enough for real research

If low-cost parts (SO-100/101 arms, a LeKiwi base, PLA and PETG prints) are combined with Hugging Face’s LeRobot framework, a robot costing under £1,000 can learn real two-handed tasks from teleoperated demonstrations.

Target: complete a task with more than 80% success.

03 · planning

Constraints first, then the build order

  • Constraints: under £1,000, printable on a home 3D printer, recyclable PLA and PETG, and fully compatible with LeRobot.
  • Objectives: design an original lift for vertical reach, extend the XLeRobot software for this robot and VR control, collect demonstration datasets, and evaluate trained policies on real tasks.
  • Approach: start from a near-stock LeKiwi to prove the software and data pipeline before designing any custom hardware.

04 · executing

v1: a working robot in six weeks

In March 2025 I built a near-stock LeKiwi with a leader–follower arm setup. Within six weeks it could be teleoperated, record data and run imitation-learning policies, with basic navigation and some dexterity.

It also showed what was missing: the base wasn’t stable, the wheels were weak, and a single low arm couldn’t reach most real tasks.

05 · iteration

v2 and v3: fixing what the robot taught me

  • v2 · Aug 2025: a new frame for height and two arms. The extra weight made the wheels sag on the motor shafts, so I added a supported axle so the chassis carries the load and the motors only drive. A Raspberry Pi 5 became a bottleneck, so I moved to a Jetson Orin Nano. After two months fighting experimental VR software, XLeRobot’s release got both arms working in VR.
  • v3 · Jan–Feb 2026: Pincopen parallel grippers, a pan-tilt head camera that follows the operator’s headset, a rack-and-pinion lift with 600 mm of travel (chosen over a lead screw for torque), an independent ESP32 e-stop that cuts motor power, and stage-aware reward annotation (SARM) for the datasets.
OB15 v2: two SO-100 arms on a tall extrusion frame above a red omni-wheel base
v2 · 2025
CAD cutaway of the wheel support that moves the load off the motor shaft
the axle fix
Close-up of a v3 arm with Pincopen parallel gripper
Pincopen grippers
Pan-tilt head camera on top of OB15
pan-tilt head camera
CAD cutaway of the rack-and-pinion lift
rack-and-pinion lift
Red emergency stop button mounted on OB15's frame
independent e-stop

06 · latest version

Results, and what’s next

About 8 hours of teleoperated data across four tasks: block transfer, putting a tool in a box, sorting blocks by colour, and mobile trash pickup. Overall success was 43%, against Mobile ALOHA’s ~90% at roughly 30× the cost. Colour sorting failed at first, then worked after targeted data collection; a clear plastic bottle on a featureless floor was the hardest case.

The lesson: data quality matters more than quantity. Next comes a centre-of-mass redesign to support tactile sensing on the grippers, a holonomic base and larger arms. Read more: the hardware → · the policy learning →

The latest OB15 build: black frame, two arms with yellow-tipped grippers, a head camera on the mast and omni-wheel base
the latest build
end-to-end: driving to the table and putting the pliers in the box
the tool-in-a-box task
OB15 v3 standing in a lab: two orange arms on a lift, omni-wheel base and orange head camera
v3 · 2026
OB15 sorting coloured blocks into matching bowls on a lab table
sorting blocks by colour
Owen presenting OB15 at Middlesex University
live demo, Middlesex University
OB15 bimanual mobile robot CAD model without covers, three-quarter view showing the extrusion frame, lift and omni-wheel base
OB15 CAD model without covers, front view
OB15 CAD model without covers, rear three-quarter view
stackROS 2 · Nav2 · SLAM · LeRobot · SmolVLA
controlMeta Quest VR, voice/LLM
datasetsOB15 datasets on Hugging Face · all of my datasets
codegithub.com/ImpurestTadpole/ob15 · telegrip_ob15 (VR teleop) · LeRobot fork · XLeRobot fork